铝格栅吊顶怎么安装才更舒适。

随着时代的发展，人们对建筑装饰越来越重视，铝格栅也成为了越来越多装饰材料中的一种，铝格栅吊顶也越来越受欢迎。铝格栅吊顶规格一般为宽度：10mm  高度：30 mm 35mm 40mm 50 mm ，宽度：15mm  高度：50 mm 60mm 80mm 90 mm  100mm 110mm 120 mm ，宽度：20mm  高度：50 mm 60mm 70mm 80mm 90 mm  100mm 110mm 120 mm 。然而铝格栅吊顶安装决不能将就，那怎么样才能不辜负自己呢？

With the development of the times, People pay more and more attention to architectural decoration , aluminum grille has become one of more and more decorative materials, aluminum grille ceiling is also more and more popular. General specification for aluminum grille ceiling is width: 10mm height: 30 mm 35mm 40mm 50 mm ;width: 15mm, height: 50 mm 60mm 80mm 90 mm 100mm 110mm 120 mm ;width: 20mm, height: 50 mm 60mm 70mm 80mm 90 mm 100mm 110mm 120 mm. However, the installation of aluminum grille ceiling can’t never be put up with , then how can we not live up ourselves?

铝格栅吊顶安装：

 aluminum grille ceiling installation ：

⑴弹线:用水准仪在房间内每个墙角上抄出水平点，弹出水准线，从水准线量至吊顶设计高度，用粉线沿墙弹出水准线。同时在混凝土顶板弹出主龙骨的位置。　

（1）snap the line: The horizontal level is removed from each corner of the room with a level instrument, and the level line is ejected , pop-up level from level to high ceiling design, snap the level line with a line along the wall . At the same time, the main keel is released on the concrete roof.

⑵固定吊挂杆件:采用膨胀螺栓固定吊挂杆件。吊杆的一端同L30*30*3角码焊接，另一端用攻丝套出大于100㎜的丝杆。吊杆用膨胀螺栓固定在楼板上，用冲击电锤打孔

The fixed hanging bar: use the expansion bolt to fix hanging bar. One end of a hanger rod is welded with L30*30*3 wire rod bracket, the other end taps out the screw mandrel that is greater than 100 mm. The hanger rod is fixed on the floor with the expansion bolt,and impact hammer drilling

⑶轻钢龙骨安装:轻钢龙骨应吊挂在吊杆上，轻钢龙骨应平行房间长向安装，同时应起拱。主龙骨的接长应采取对接，相邻龙骨的对接接头要相互错开。轻钢龙骨挂好后应基本调平。跨度大于15m以上的吊顶，应在主龙骨上，每隔15m加一道大龙骨，并垂直主龙骨焊接牢固。

（3）Installation of the light steel keel: light steel keel should be hung on the hanger rod, light steel keel should be parallel to the long room installation, at the same time,it should be in an arch. The length of the main keel should be butted, and the butt joints of adjacent keels shall be staggered with each other. Light steel keel should be basically leveling after hanging. The ceiling with a span greater than 15m shall be on the main keel, plus a big keel at intervals of 15m, and be welded firmly to the vertical main keel.

⑷弹簧片安装:用吊杆与轻钢龙骨连接，间距900㎜～1000㎜，再将弹簧片卡在吊杆上。

（4）The spring strip installation: boom is connected with the light steel keel spacing of 900 mm to 1000 mm, Then clip the spring onto the boom.

⑸格栅主副骨组装:将格栅的主副骨在下面按设计图纸的要求预装好。

(5)The main side grille assemble: the main and side bone grille are assembled below according to the requirements of design drawings with good.

⑹格栅安装:将预装好的格栅天花用吊钩穿在主骨孔内吊起，将整栅的天花连接后，调整至水平。

（6）Grille installation: the pre packaged grille ceiling is hung by the hook in the main bone hole, after the whole grille ceiling connected, adjusted it to the level of.

佛山建威铝格栅厂家是专业生产和销售铝扣板吊顶，如果您想了解更多铝格栅产品，请点击登录建威官网：http://www.fsjwlth.com或咨询我们的业务经理罗小姐，她的电话/微信：13924844954

Foshan Jian Wei aluminum grille factory is specialized in the production and sale aluminum grille ceiling, if you want to know more about the aluminum grille production, please click on the website: http://www.fsjwlth.com.Or consult our business manager, Miss Luo, on her phone / WeChat: 13924844954