ZYD-3F1 环压强度试验式样座

武汉格莱莫检测设备有限公司  

电话：13545068882；027-86619889

传真：027-86619889  

http://www.glmgs.com/prodxx.asp?id=769


一、产品简介
　　该产品是压缩试验仪上测定纸和纸板环压强度的辅助器具，具根据国家标准GB／T2679.8《纸和纸板环压强度的测定》中关于试样座的规定设计而成。本器具由一个试样座和十三种不同尺寸规格的中心盘组成，可适应不同厚度的试样，广泛应用于造纸、包装和产品质量监督检验等行业和部门。
二、使用方法　　
    ★根据试样厚度选择相应尺寸的中心盘，每个中心盘所对应的试样厚度范围以“X.XX－X.XX”的形式标注在中心盘上平面上。
    ★将选择好的中心盘装入试样座中。
    ★将试样沿试样座的缺口插入，在试样插入一部分后，用手拉住在槽内的试样另一头，沿圆弧方向转一圈，至试样进入试样座且试样接头试样座缺口为止。
    ★用手轻拍试样端面，确保试样落入试样座的底部。注意用力要轻，不能损伤试样。
    ★将装好试样的试样座放入压缩试验仪下压板的中部，并将试样座的缺口面向操作员，然后按压缩试验仪的操作步骤进行环压试验。




一、产品简介
One, product introduction
　　该产品是压缩试验仪上测定纸和纸板环压强度的辅助器具，具根据国家标准GB／T2679.8《纸和纸板环压强度的测定》中关于试样座的规定设计而成。本器具由一个试样座和十三种不同尺寸规格的中心盘组成，可适应不同厚度的试样，广泛应用于造纸、包装和产品质量监督检验等行业和部门。
The product is compression test instrument on the ring crush strength of paper and board - Determination of essential auxiliary apparatus, according to the national standard GB / T2679.8 " paper and board - Determination of ring crush strength " on the specimen holder designed the provisions. The apparatus comprises a specimen holder and thirteen different sizes of the center plate, and can adapt to different thickness of the specimen, widely used in papermaking, packaging and product quality supervision and inspection and other industries and sectors.
二、使用方法　　
Two, the use of methods
★根据试样厚度选择相应尺寸的中心盘，每个中心盘所对应的试样厚度范围以“X.XX－X.XX”的形式标注在中心盘上平面上。
★according to specimen thickness corresponding to selected dimensions of the center plate, the center of each plate corresponding to the specimen thickness range to " X.XXX.XX " in the form of annotation in the center disc on a plane.
★将选择好的中心盘装入试样座中。
★ will choose a good center disc into sample holder.
★将试样沿试样座的缺口插入，在试样插入一部分后，用手拉住在槽内的试样另一头，沿圆弧方向转一圈，至试样进入试样座且试样接头试样座缺口为止。
★the sample along the specimen holder gap insertion, the specimen in the insertion portion, pulling in groove specimen another head, along the arc direction to a circle, to the sample into the sample holder and the sample joints Miss specimen holder notch.
★用手轻拍试样端面，确保试样落入试样座的底部。注意用力要轻，不能损伤试样。
★hand pat specimen ends, to ensure the sample into the sample holder at the bottom. Note that force must be light, can not damage the sample.
★将装好试样的试样座放入压缩试验仪下压板的中部，并将试样座的缺口面向操作员，然后按压缩试验仪的操作步骤进行环压试验。
★ will install sample sample seat into a compression tester bottom board of the central, and the sample holder notch oriented, then according to the compression tester operation steps ring crush test.