你好,欢迎来到世铝网 [请登录] [免费注册]
世铝网 铝业设备
您当前的位置: 世铝网 铝业设备 其它 LX-A双针邵氏硬度计 普通会员

LX-A双针邵氏硬度计

加入收藏 举报
详细信息
 

武汉格莱莫检测设备有限公司  

电话:13545068882027-86619889

传真:027-86619889  

网址:www.glmgs.com

http://www.glmgs.com/prodxx.asp?id=587

一、产品简介
    LX邵氏A型硬度计广泛应用于中低硬度塑料、各类橡胶、多元脂、皮革、蜡等的硬度测试。ISO868 和 ISO7619国际标准生产,符合 GB/T531 、JB6148 和 JJG304 标准。指针式指示,读数方便、准确、精度高;手持式设计,携带方便,可手持测量,也可安装在配套的测试架上测试。
二、技术指标
    ★刻度盘值:0 ~ 100HA;
    ★压针行程:2.5 mm;
    ★推荐测量范围:10 ~ 90HA;
    ★压针头部尺寸:Ф 0.79 mm;
    ★重 量:0.5 kg。
三、使用方法
    把试样放置在坚固的平面上,拿住硬度计,压足中孔的压针距离试块边缘至少12mm,平稳地把压足压在试样上,不能有任何振动,并保持压足平行于试样表面,以使压针垂直地压入试样,所施加的力要刚好足以使压足和试样完全接触,除另有规定,在压足和试样完全按触后1秒内读数,如果是其他间隔时间读数则说明,在试样相距至少6mm的不同位置测量硬度值5次,取其平均值。
    使用须知:
    ★测定前应检查硬度计的指针在自由状态下应指向零位。如指针量偏离零位时,可以松动右上角压紧螺钉,转动表面,对准零位。然后将硬度计压在玻璃板上,压针端面与压足底面紧密接触于玻璃板上时,指针应指向100+/-1HA,如不指向100+/-1HA时,可轻微按动压针几次,如仍不指100+/-1HA时,则此硬度计不能使用。如在邵氏硬度计测试机架上使用时,可拨动手柄,使工作台上升至定荷砝码抬起,使压针端面与压足平面紧密接触于玻璃工作台时,指针应指向100+/-1HA。如不指100+/-1HA时, 可调整工作台平面的调节螺钉,若调整后指针仍不指100+/-1HA时,好送生产单位调整为宜。
    ★橡胶的试样及试验温度要求; ①、橡胶的试样厚度不小于6mm,宽度不小于15mm,长度不小于35mm,试样厚度不足6mm时,可用同样胶片重叠测定,但不超过3层。并要求胶片上下平行。 ②、检定时室温为23℃±5℃,检定前硬度计在此温度下至少存放1小时。
    ★塑料试样及试验温度要求; ①、塑料试样为正方形,边长50mm、厚度6mm。也允许采用50×15mm的试样。 ②、在可能的情况下,试样在测试前应按照GB/T2941-1991规定在实验室标准温度下进行调节。比对试验或系列试验在相同温度下进行。
    ★橡胶及塑料试样表面均应光滑、平整、不应有机械损伤及杂质等缺陷。
    ★硬度计使用35000次后,建议每使用10000次左右按GB531规定检查弹簧压力与指针刻度关系及压针端部的形状尺寸。
    ★硬度计使用完毕后,装入仪器盒或仪器箱内,放置干燥处,防止受潮。
    ★定荷测定架上的升降小轴和工作台底部,请注意经常揩擦干净,涂少量防锈油,以防生锈。
    ★使用邵氏硬度计时,当A型硬度计示值低于10HA时是不准确的,测量结果不能使用。A型硬度计测量值超出90HA时推荐使用D型硬度计。




一、产品简介
One, product introduction
LX邵氏A型硬度计广泛应用于中低硬度塑料、各类橡胶、多元脂、皮革、蜡等的硬度测试。ISO868 和 ISO7619国际标准生产,符合 GB/T531 、JB6148 和 JJG304 标准。指针式指示,读数方便、准确、精度高;手持式设计,携带方便,可手持测量,也可安装在配套的测试架上测试。
LX shore A hardness is widely applied in the low hardness, all kinds of rubber, plastic, leather, wax and other multiple fat hardness test. ISO868 and ISO7619 international standards of production, with GB/T531, JB6148 and JJG304 standards. Pointer type indicator, reading is convenient, accurate, high precision; handheld design, easy to carry, can be a hand-held measurement, can also be mounted on a supporting test rack test.
二、技术指标
Two, technical indicators
★刻度盘值:0 ~ 100HA;
★dial value: 0~ 100HA;
★压针行程:2.5 mm;
★pressure stroke of the needle: 2.5 mm;
★推荐测量范围:10 ~ 90HA;
★recommend measuring range: 10~ 90HA;
★压针头部尺寸:Ф 0.79 mm;
★ press needle head size:Φ0.79 mm;
★重 量:0.5 kg。
★weight: 0.5 kg.
三、使用方法
Three, the use of methods
把试样放置在坚固的平面上,拿住硬度计,压足中孔的压针距离试块边缘至少12mm,平稳地把压足压在试样上,不能有任何振动,并保持压足平行于试样表面,以使压针垂直地压入试样,所施加的力要刚好足以使压足和试样完全接触,除另有规定,在压足和试样完全按触后1秒内读数,如果是其他间隔时间读数则说明,在试样相距至少6mm的不同位置测量硬度值5次,取其平均值。
A sample is placed in a rigid plane, seized the hardness tester, pressure foot hole pressure needle distance test block edge of at least 12mm, smooth the pressure foot pressure to the specimen, there can be no vibration, and keep the pressure foot parallel to the surface of the specimen, so that pressure vertical pin pressed into the sample, applied force to be just enough to make the pressure foot and sample full contact, unless otherwise specified, must be in the pressure foot and specimen in contact after a second reading, if it is the other interval time readings must explain, in the sample are separated by at least 6mm different position measuring hardness 5, take the average.
使用须知:
Instructions for use:
★测定前应检查硬度计的指针在自由状态下应指向零位。如指针量偏离零位时,可以松动右上角压紧螺钉,转动表面,对准零位。然后将硬度计压在玻璃板上,压针端面与压足底面紧密接触于玻璃板上时,指针应指向100+/-1HA,如不指向100+/-1HA时,可轻微按动压针几次,如仍不指100+/-1HA时,则此硬度计不能使用。如在邵氏硬度计测试机架上使用时,可拨动手柄,使工作台上升至定荷砝码抬起,使压针端面与压足平面紧密接触于玻璃工作台时,指针应指向100+/-1HA。如不指100+/-1HA时, 可调整工作台平面的调节螺钉,若调整后指针仍不指100+/-1HA时,好送生产单位调整为宜。
Determination of hardness of should be examined before a pointer in a free state should point zero. Such as pointer volume deviation from zero, can loosen the upper right corner of a compression screw, rotating surface, zero. Then the hardness pressure in a glass plate, needle pressing and the end surface of the plantar surface of pressure tight contact with the glass plate, a pointer pointing to 100+/-1HA, if not to the 100+/-1HA, may be slightly pressing the needle pressing several times, such as not to 100+/-1HA, the hardness can not use. As in the Shaw hardness testing machine frame when in use, the handle, so that the table up to the fixed charge weight lifted, so that pressure needle end with pressure foot plane in tight contact with the glass table, pointer pointing to 100+/-1HA. If not a 100+/-1HA, can adjust the work table surface of the adjusting screws, if the pointer is adjusted to 100+/-1HA, it is best to send units of production adjustment is appropriate.
★橡胶的试样及试验温度要求; ①、橡胶的试样厚度不小于6mm,宽度不小于15mm,长度不小于35mm,试样厚度不足6mm时,可用同样胶片重叠测定,但不超过3层。并要求胶片上下平行。 ②、检定时室温为23℃±5℃,检定前硬度计在此温度下至少存放1小时。
★rubber samples and test temperature; 1, rubber specimen thickness not less than 6mm, with width not less than 15mm, length not less than 35mm, sample thickness less than 6mm, used the same film overlap measure, but not more than 3 layers. And asked to film in parallel. ②, test at room temperature 23± 5 ℃, verification before the hardness at this temperature for 1 hours at least.
★塑料试样及试验温度要求; ①、塑料试样为正方形,边长50mm、厚度6mm。也允许采用50×15mm的试样。 ②、在可能的情况下,试样在测试前应按照GB/T2941-1991规定在实验室标准温度下进行调节。比对试验或系列试验在相同温度下进行。
★plastic sample and test temperature; 1, plastic sample is square, side length 50mm, thickness 6mm. Also allow for the use of 50 × 15mm specimen. ②, where possible, the sample before the test should be in accordance with the provisions of GB/T2941-1991 in laboratory standard temperature regulation. Comparison test or series of tests must be at the same temperature.
★橡胶及塑料试样表面均应光滑、平整、不应有机械损伤及杂质等缺陷。
★rubber and plastic surface shall be smooth, flat, not due to mechanical damage and impurities and other defects.
★硬度计使用35000次后,建议每使用10000次左右按GB531规定检查弹簧压力与指针刻度关系及压针端部的形状尺寸。
★hardness after used for 35000 times, every use of about 10000 times as specified in the GB531 check spring pressure and pointer scale relation and pressure needle end shape and size.
★硬度计使用完毕后,装入仪器盒或仪器箱内,放置干燥处,防止受潮。
★hardness after use, into the box of the instrument or apparatus box, dry place, prevent moisture.
★定荷测定架上的升降小轴和工作台底部,请注意经常揩擦干净,涂少量防锈油,以防生锈。
Determination of fixed charge frame lifting small axis and at the bottom of the working platform, please note often wipe clean, apply a small amount of oil, to prevent rusting.
★使用邵氏硬度计时,当A型硬度计示值低于10HA时是不准确的,测量结果不能使用。A型硬度计测量值超出90HA时推荐使用D型硬度计。
★use shore hardness testers, when A durometer value is less than 10HA is not accurate, the measurement results can not be used. A durometer value exceeds 90HA recommend using D hardness meter.

联系方式
  • 联系人: 徐海柱 先生
  • 职位: 销售经理
  • 真: 027-86619889
  • 电话: 027-86619996
  • 手机: 13545068882
  • 址: 湖北省 武汉市 徐东大街51号
供应商其他供应信息
还没找到合适的产品?
  • 01
  • 快速发布求购信息
  • 下一步
  • 02
  • 试试以下相关搜索:
  • 03
  • 联系cnal客服:
  • 致电: 0371-63388900
    马上启动您的快速采购通道!